Services tailored to your yacht's needs

AWLGRIP's laboratories have developed a revolutionary new coating-AWLGARD® Interior Urethane. AWLGARD® Interior Urethane is designed for use where a durable urethane is required and the application of a solvent borne coating is impractical. Typical applications include engine rooms, lazarettes, showers, and bulkheads. This two-component urethane has excellent solvent resistance to denatured alcohol and acetone, as well as diesel fuel and anti-freeze. AWLGARD®'s water reducible technology provides a product with low odour and a flash point greater than 200°F.

Painters rave about the desirable application characteristics including quick tack times, extended pot life, and superior flow and levelling. AWLGARD® Interior Urethane has excellent gloss retention, heat resistance to 180°F, shelf stability, and superior hiding characteristics. AWLGARD®'s standard colours for interiors include Cloud White, Matterhorn White, Snow White, and Light Gray. All colours can be applied by spray, brush, or roller. For more information on this product please contact us on our contact page.

The do's and don'ts of AWLGRIPR the questions you have, answered officially.

DO:

1. Regular Cleaning will avoid build of dirt. grease and other contaminants which can slowly cause premature aging of AWLGRIPR or AWLCRAFT® 2000. This premature aging can cause the finish to appear dull.

Wash the surface regularly with fresh water and AWLWASHTM Wash Down Concentrate (73234) which is formulated to clean AWLGRIP and AWLCRAFT® 2000 topcoats. AWLWASH does not contain alkalies, acids, or abrasives. Some "marine soaps" are not suitable for use on painted surfaces. When using AWLWASHTM, it is important to dilute as specified on the label.

When washing it is important to keep the surface wet to prevent AWLWASH from drying on the surface. Use soft, non- abrasive cloths, sponges or washing mits when washing.

Thoroughly rinse all surfaces with fresh water after washing to remove all detergent residue. A water softener is recommended to eliminate hard water residue. Wiping the surface dry with a chamois or soft cotton towel is recommended.

If water spots occur, they can be removed with AWLCARETM Protective Polymer Sealer (73240).

ONLY:

2. AWLGRIP Solvents such as AWL-PREP -T0008. AWL-PREP® PLUS-T0115 (or T0340

Surface Cleaner in Europe), AWL-PREP® 400-T0170, toluene, lacquer thinner.

M.E.K, acetone, or kerosene may be used to soften or remove heavy build-up of grease and grime, felt tip markings, or aerosol spray paint on the AWLGRIP Topcoat

AWLCRAFT® 2000 ONLY: Use only milder solvents to remove stubborn stains. AWL PREP® TO008, AWL-PREP® 400-T0170,

DO NOT

1. Do not use traditional waxes. General: Traditional waxes break down rapidly. The residue can cause the topcoat to appear yellow, plus it attracts dirt. This creates the need to maintain the wax, increasing overall maintenance. Traditional waxes which contain no abrasives probably do little harm to the coating, but offer no benefit.

AWLGRIP has developed AWLCARETM Protective Polymer Sealer (73240) for those who want to enhance their finish and need the additional cleaning power of a hand applied, dry wash product. AWLCARETM is a non-yellowing sealer that will protect both AWLGRIP and AWLCRAFT® 2000 with regular applications. Hand applied AWLCARETM will not harm AWLGRIP's topcoats and can easily be removed with AWL-PREP® PLUS-T0115 (or T0340) Surface Cleaner in Europe) when it is time to repaint.

AWLGRIP Only: Regular applications of

AWLCARETM will help temporarily seal and restore shine to painted surfaces that have become porous due to age or mistreatment, helping to maintain a satisfactory

appearance until there is time to repaint.

AWLCRAFT® 2000 Only: AWLCARETM Protective Polymer Sealer will help maintain the gloss on AWLCRAFT 2000 topcoats with regular applications. Especially those which have been buffed or polished. Remember, AWLCARETM is only applied and buffed by hand. Never apply or buff AWLCARETM with a machine.

2. Do not use abrasives, scratch pads, or compounds. Scratching the surface gives dirt a place to cling while wearing out the resin layer. Using abrasives of any kind will reduce the overall life of the finish and voids the AWLGRIP® Limited Warranty.

3. Do not allow contact between AWLGRIP or AWLCRAFT® 2000 Topcoat and teak cleaners. Most teak cleaners